Eeger Beever™ 812 Brush Chipper

Perfect for rental yards, landscapers, golf courses and pruning crews, the high-capacity Eeger Beever 812 Brush Chipper is easy to transport and operate. Plus, it’s the only chipper in its class to combine both a wide infeed chute opening and 1.25″ (3.17 cm) thick chipping disc for a greater chipping capacity than comparable models. The 812 has a 251-pound (114 kg) disc and shaft weight, which provides more inertia to power through material and continuously feed material. With a single top feed wheel compression system and 32.3 ci hydraulic motor with spring-assisted down pressure, the 812 generates more than 2,300 lb/ft (3,118 Nm) of material pulling force and approximately 1,000 lb/ft (1,356 Nm) of combined down pressure to easily feed a variety of materials.

Like all Morbark equipment, the 812 is a long-lasting, durable machine backed by a world-class parts and service support team.

Belt Drive

Direct drive with belt power transfer eliminates clutch components and over center belt tensioning systems, reducing problem areas and easing maintenance burdens.

Infeed Chute

Infeed chute with 96-square-inch throat opening allows for easy material feeding and reduced trim labor and folds to reduce transport and storage length.

360° Swivel Discharge

360° swivel discharge with adjustable chip deflector puts chips right where they’re needed without removing the chipper from the tow vehicle.

Feed System

A top feed wheel compression system with spring-assisted down pressure easily breaks down a variety of materials.

General

Height: 7’4″ (2.24 m)
Width: 5’3″ (1.6 m)
Length (transport) : 12′ (3.66 m)
Length (operating): 13’10” (4.22 m)


Gross weight (approximate): 2,500 lb (1,134 kg)

Suspension: 2,500 lb (1,134 kg) Torflex


Infeed opening: 24.5″ high x 33.5″ wide (62.23 cm x 85.09 cm)
Throat opening: 8″ high x 12″ wide (20.32 cm x 30.48 cm)
Feed wheel: 11.5″ wide x 9″ diameter (29.21 cm x 22.86 cm)
Disc dimensions: 1.25″ thick x 28″ diameter (3.17 cm x 71.12 cm)


Engine: Briggs & Stratton/Vanguard
Horsepower: 37 HP (27.6 kW)


Fuel capacity (tank): 10 gallons (37.85 litre)
Hydraulic oil capacity: 10 gallons (37.85 litre)


Frame: 2″ x 4″ Tubular (5.08 cm x 10.16 cm)

Tires:  (2) 185/75Rx14 – 8-ply

Hitch: 2″ Ball (5.08 cm)


Equipment Highlights

Direct drive with belt power transfer

Automatic feed system

Chipper disc with two 10.5″ x 4″ x .375″ (26.67 cm x 10.16 cm x 9.52 mm) dual‑edged chipper knives and four full-length, bolt-on, chip throwing paddles

Reversible feed works control bar and dual safety cables located within infeed chute

Pinned chipper hood access with integrated hood safety device to disconnect the start system when the chipper hood is opened and allow ease of disc maintenance.

3″ x 4″ (7.62 cm x 10.16 cm) tubular steel fixed length drawbar and .375″ (9.52 mm)  thick safety chains with clasp hooks

Fuel tank sight gauge, drain plug and shut‑off valve

Hydraulic tank shut-off valve, drain plug, clean-out cover and vented filter head assembly with dipstick to check oil level

8D, 1400 CCA Battery


Options

  • ChipSafe® Operator Safety Shield
  • Variable speed flow control
  • 2,500 lb (1,135 kg) Torflex suspension axle with electric brake system, electric brake actuator and 185R14 tires with rims
  • Custom paint and logo packages
  • Knife saver tool
  • Engine stop on infeed
  • Pusher paddle
  • Spanish and English safety decals
Specifications may vary with equipment options.
Morbark Knives

Morbark Knives: High Performance. Higher Value.

Morbark knives give you:

  • Morbark Durability
  • Improved Quality
  • Better Value
You may also be interested in…