Perfect for rental yards, landscapers, golf courses and pruning crews, the high-capacity Beever M8D Brush Chipper is easy to transport and operate. Plus, it’s the only chipper in its class to combine both a wide infeed chute opening and 1 1/4″ (3.17 cm) thick chipping disc for a greater chipping capacity than comparable models. The M8D has a 251-pound (114 kg) disc and shaft weight, which provides more inertia to power through material and continuously feed material.
With a single top feed wheel compression system and 32.3 ci hydraulic motor with spring-assisted down pressure, the M8D generates more than 2,300 lb./ft. (7,545 lb./m.) of material pulling force and approximately 1,000 lb./ft. (3,280 lb./m.) of combined down pressure to easily feed a variety of materials.
Like all Morbark equipment, the M8D is a long-lasting, durable machine backed by a world-class parts and service support team.
Direct drive with belt power transfer eliminates clutch components and over center belt tensioning systems, reducing problem areas and easing maintenance burdens.
Infeed chute with 96-square-inch throat opening allows for easy material feeding and reduced trim labor and folds to reduce transport and storage length.
360° Swivel Discharge
360° swivel discharge with adjustable chip deflector puts chips right where they’re needed without removing the chipper from the tow vehicle.
A top feed wheel compression system with spring-assisted down pressure easily breaks down a variety of materials.
Chipping Capacity: 8″ (20.32 cm)
Height: 7’4″ (2.35 m)
Width: 5’3″ (1.6 m)
Length (transport) : 12′ (3.66 m)
Length (operating): 13’10” (4.22 m)
Gross weight (approximate): 2,500 lbs. (1,135 kg)
Suspension: 2,500 lb. (1,135 kg) Torflex
Infeed opening: 33 ½” wide x 24 ½” high (85.09 cm x 62.23 cm)
Throat opening: 12″ wide x 8″ high (30.48 cm x 20.32 cm)
Feed wheel: 11 ½” wide x 9″ diameter (29.21 cm x 22.86 cm)
Disc dimensions: 1 ¼” thick x 28″ diameter (3.17 cm x 71.12 cm)
Engine: Kohler or Kubota
Horsepower: 35–44 HP (26—33 kW)
Fuel capacity (tank): 10 gallons (37.85 litre)
Hydraulic oil capacity: 10 gallons (37.85 litre)
Frame: 2″ x 4″ Tubular (5.08 cm x 10.16 cm)
Tires: (2) 185/75Rx14 – 8-ply
Hitch: 2″ Ball (5.08 cm)
Direct drive with belt power transfer
Automatic feed system
Chipper disc with two 10 ½” x 4″ x 3/8″ (26.67 cm x 10.16 cm x 9.52 mm) dual‑edged chipper knives and four full-length, bolt-on, chip throwing paddles
Reversible feed works control bar and dual safety cables located within infeed chute
Pinned chipper hood access with integrated hood safety device to disconnect the start system when the chipper hood is opened and allow ease of disc maintenance.
3″ x 4″ (7.62 cm x 10.16 cm) tubular steel fixed length drawbar and 3/8″ (9.52 mm) thick safety chains with clasp hooks
The Morbark Paint System is a Super-Shield® topcoat and two-component, high-performance, isocyanate-free, urethane system. The topcoat is high-solids, low-VOC, and offers long-term color and UV protections, as well as resistance to a wide range of chemicals, pollutants, and natural weathering. The system utilizes automotive grade pigments in the Super-Shield topcoat to achieve outstanding color and gloss protection. The system has also been tested to meet many military-grade standards for long-term performance. (Super-Shield is a registered trademark of Cloverdale Paint Inc.)
Fuel tank sight gauge, drain plug and shut‑off valve
Hydraulic tank shut-off valve, drain plug, clean-out cover and vented filter head assembly with dipstick to check oil level
8D, 1400 CCA Battery
- ChipSafe® Operator Safety Shield
- Variable speed flow control
- 2,500 lb. (1,135 kg) Torflex suspension axle with electric brake system, electric brake actuator and 185R14 tires with rims
- Custom paint and logo packages
- 2 ½” (6.35 cm) lunet ring
- Knife saver tool
- Engine stop on infeed
- Material pushing tool
- Spanish and English safety decals