Beever™ M15R Brush Chipper

Our Beever™ M15R brush chipper is ideal for residential tree services, utility line clearing, vegetation management, maintenance contractors and municipalities, this high-capacity, high-production chipper includes more standard features than any other chipper in its class. The Beever M15R Brush Chipper is also available tracked for right of way clearing, highway clean-ups and hard-to-reach areas requiring a self-propelled unit for material access.

The powerful TorqMax™ dual feed wheel compression system generates more than 6,600 lb./ft. of material pulling force. Many customer-inspired innovations are featured on the M15R, increasing efficiency and safety while reducing operating and maintenance costs. Unit is pre-plumbed and outfitted for the easy installation of most aftermarket components. Ergonomic infeed design provides consistent feed control bar activation.

Like all Morbark equipment, the M15R is a long-lasting, durable machine backed by a world-class parts and service support team.

Beever M15R chipper drum


30″ diameter four-knife staggered knife-pocket drum with patented removable knife holders and Vortex chambered air-impeller system provides maximum chipping efficiency.

Beever M14R Channel Fram

Channel Frame

The 8.2 lb., 6″ channel frame rails with 2″ x 6″ tubular steel frame with cross bracing increases structural strength while maintaining low unit weight.

Beever M15R Reversing Auto-feed

Reversing Auto-feed

The reversing auto-feed system automatically stops forward feed and briefly backs material away from the drum for optimum engine performance while chipping.

Beever M18R Hydraulic Down Pressure

Hydraulic Down Pressure

The Variable Force™ Hydraulic Down Pressure System eliminates the use of springs and creates up to 4,500 lbs. of perpetual down pressure.

M12R Tracks

Track Undercarriage: Optional

Take the chipper to the material with 400mm rubber tracks, 4.84 PSI ground pressure, low-speed travel range of 1.0 MPH and high-speed travel range of 1.8 MPH.


Chipping capacity: 15″

Height: 8’11” wheeled/ 8’6″ tracked
Width: 7’3″ wheeled/ 7’10” tracked
Length: 18’1″ wheeled/ 16′ tracked

Gross weight (approximate): 8,900 lbs. wheeled/ 13,500 lbs. tracked
Suspension: 9,000 lb. Torflex

Infeed opening: 56″ wide x 37″ high
Throat opening: 20 ½” wide x 18″ high wheeled/ 20 ½” wide x 15″ high tracked

Drum: 23 ¾” wide x 30″ diameter

Engine: CAT, Cummins, GM, John Deere or Perkins
Horsepower: 130–174 HP

Fuel capacity: 32 gallons
Hydraulic oil capacity: 12 gallons wheeled/ 26 gallons tracked

Frame: 8.2 lb. 6″ channel wheeled/ 6″ x 2″ x 1/4″ wall tube

Tires : (2) 215/75Rx17 ½” / Rubber track undercarriage

Hitch: 2 ½” Pintle

Equipment Highlights

Dual horizontal feed wheels with TorqMax top feed wheel compression system, hydraulic lift assist, Variable Force constant hydraulic down pressure system with additional manually applied hydraulic down pressure at the valve handle and direct drive bottom feed wheel with torque arm coupler

Live hydraulic system including: ball valve, pump, motor, and valve bank with additional pre-plumbed valve section for installation of an aftermarket winch package

3″ x 5″ tubular steel telescoping drawbar with two 12″ extensions

Morthane Paint System: A chemically cured, electrostatically applied urethane coating with high-gloss finish, built-in UV protection, chip and chemical resistance and corrosion protection


  • ChipSafe® Operator Safety Shield
  • Winch package: heavy-duty, 5,000 lb. pull capacity with rope and 10′ chafe guard
  • Bottom Bump Bar
  • Hydraulic Swivel Discharge
  • Cone Holder
  • Spare Tire/Mount
  • Folding Infeed Tray
  • Flow Control
  • Axle Options Available
  • Fender Options Available
  • Battery Box Options Available
Specifications may vary with equipment options.
Bevel Buddy™ makes chipping more profitable

Bevel Buddy™ makes chipping more profitable

Re-sharpen knives without removing from machine for less downtime and more production!

You may also be interested in…